About us


Updated 2020/09/18

Unfortunately, We are already sold out.

Moisture content
Charcoal fresh from an opened kiln contains very little moisture, usually less than 1%. Absorption of moisture from the humidity of the air itself is rapid and there is, with time, a gain of moisture which even without any rain wetting can bring the moisture content to about 5 to 10%, even in well-burned charcoal. When the charcoal is not properly burned or where pyroligneous acids and soluble tars have been washed back onto the charcoal by rain, as can happen in pit and mound burning, the hygroscopitity of the charcoal is increased and the natural or equilibrium moisture content of the charcoal can rise to 15% or even more.

Moisture is an adulterant which lowers the calorific or heating value of the charcoal. Where charcoal is sold by weight, keeping the moisture content high by wetting with water is often practised by dishonest dealers. The volume and appearance of charcoal is hardly changed by addition of water. For this reason bulk buyers of charcoal prefer to buy either by gross volume, e.g. in cubic metres, or to buy by weight and determine by laboratory test the moisture content and adjust the price to compensate. In small markets sale is often by the piece.

It is virtually impossible to prevent some accidental rain wetting of charcoal during transport to the market but good practice is to store charcoal under cover even if it has been bought on a volume basis, since the water it contains must be evaporated on burning and represents a direct loss of heating power. This occurs because the evaporated water passes off into the flue and is rarely condensed to give up the heat it contains on the object being heated in the stove.

Quality specifications for charcoal usually limit the moisture content to around 5-15% of the gross weight of the charcoal. Moisture content is determined by oven drying a weighed sample of the charcoal. It is expressed as a percentage of the initial wet weight.

There is evidence that charcoal with a high moisture content (10% or more) tends to shatter and produce fines when heated in the blast furnace, making it undesirable in the production of pig iron.

Volatile matter other than water
The volatile matter other than water in charcoal comprises all those liquid and tarry residues not fully driven off in the process of carbonization. If the carbonization is prolonged and at a high temperature, then the content of volatiles is low. When the carbonization temperature is low and time in the kiln is short, then the volatile matter content increases.

These effects are reflected in the yield of charcoal produced from a given weight of wood. At low temperatures (300°C) a charcoal yield of nearly 50% is possible. At carbonization temperatures of 500-600°C volatiles are lower and retort yields of 30% are typical. At very high temperatures (around 1000°C) the volatile content is almost zero and yields fall to near 25%. As stated earlier, charcoal can reabsorb tars and pyroligneous acids from rain wash in pit burning and similar processes. Thus the charcoal might be well burned but have a high volatile matter content due to this factor. This causes an additional variation in pit burned charcoal in wet climates. The resorbed acids make the charcoal corrosive and lead to rotting of jute bags – a problem during transport. Also it does not burn cleanly.

The volatile matter in charcoal can vary from a high of 40% or more down to 5% or less. It is measured by heating away from air, a weighed sample of dry charcoal at 900°C to constant weight. The weight loss is the volatile matter. Volatile matter is usually specified free of the moisture content, i.e. volatile matter – moisture or (V.M. – moisture).

High volatile charcoal is easy to ignite but may burn with a smoke flame. Low volatile charcoal is difficult to light and burns very cleanly. A good commercial charcoal can have a net volatile matter content – (moisture free) of about 30%. High volatile matter charcoal is less friable than ordinary hard burned low volatile charcoal and so produces less fines during transport and handling. It is also more hygroscopic and thus has a higher natural moisture content.

Fixed carbon content
The fixed carbon content of charcoal ranges from a low of about 50% to a high or around 95%. Thus charcoal consists mainly of carbon. The carbon content is usually estimated as a “difference”; that is to say, all the other constituents are deducted from 100 as percentages and the remainder is assumed to be the % of “pure” or “fixed” carbon. The fixed carbon content is the most important constituent in metallurgy since it is the fixed carbon which is responsible for reducing the iron oxides of the iron ore to produce metal. But the industrial user must strike a balance between the friable nature of high fixed carbon charcoal and the greater strength of charcoal with a lower fixed carbon and higher volatile matter content to obtain optimum blast furnace operation.

Ash content
Ash is determined by heating a weighed sample to red heat with access of air to burn away all combustible matter. This residue is the ash. It is mineral matter, such as clay, silica and calcium and magnesium oxides, etc., present in the original wood and picked up as contamination from the earth during processing.

The ash content of charcoal varies from about 0.5% to more than 5% depending on the species of wood, the amount of bark included with the wood in the kiln and the amount of earth and sand contamination. Good quality lump charcoal typically has ash content of about 3%. Fine charcoal may have a very high ash content but if material less than 4 mm is screened out the plus 4 mm residue may have an ash content of about 5-10%. Buyers naturally suspect fine charcoal and it is difficult to sell (and use, unfortunately).